濟南鍛件廠在生產鍛件的過程中的能耗主要是燃料消耗，大部分廠家采用天然氣，是鍛造廠生產中的主要能源消耗。在重型鍛造廠燃料消耗占各種能耗的80%以上。對于鍛造廠降低鍛件爐耗意義重大，常用的措施是：

　　The main energy consumption in the process of producing forgings in Ji'nan is the fuel consumption. Most of the manufacturers use natural gas, which is the main energy consumption in the forging plant. In the heavy forging plant, fuel consumption accounts for more than 80% of the energy consumption. It is of great significance for the forge to reduce the furnace consumption of forgings:

　　1、采用合理熱源：大部分廠家采用天然氣，天然氣不僅成本低，還能享受補助，而且也長久對環境污染小。

　　1, the use of reasonable heat source: most manufacturers use natural gas, natural gas is not only low cost, but also enjoy subsidies, but also for a long time, small environmental pollution.

　　2、采用先進的加熱爐型，毛坯、鍛件燃氣加熱爐采用數字化蓄熱式高速脈沖燃燒和控制技術及連續供給燃料蓄熱式脈沖燃燒和控制技術。對比采用常規高速燒嘴+空氣預熱器的燃燒方式，應用于高溫鍛造加熱爐，節能率高達50%，爐溫均勻性控制在±10℃之間，應用于中、低溫熱處理爐，節能率達30-50%，爐溫均勻性控制在±5℃之間。

　　2. Adopt advanced heating furnace type, blank and forging gas heating furnace, adopt digital regenerative high speed pulse combustion and control technology, and continuously supply fuel regenerative pulse combustion and control technology. Compared with conventional combustion mode high speed burner + air preheater, used in hot forging heating furnace, energy saving rate of 50%, the temperature uniformity between - 10 DEG C, used in medium and low temperature heat treatment furnace, energy saving rate is 30-50%, the temperature uniformity is controlled within 5 deg.

　　3、采用熱料裝爐工藝：熱料裝爐是進行大鍛件加熱的有效節能措施，鍛造廠車間入爐加熱，一般入爐溫度控制在600℃以上。與冷料裝爐相比，可節能40-45%，同時可以節省加熱時間，減少加熱配置數量，提高生產效率。

　　3. Adopting hot material charging process: hot material charging is an effective energy saving measure for heating large forgings. The furnace temperature is controlled more than 600 DEG C in the forge workshop. Compared with the cold charging furnace, the utility model can save energy 40-45%, and can save heating time, reduce heating configuration quantity and improve production efficiency.

　　4、余熱回收技術，燃料爐中排出的煙氣溫度高達600-1200℃，帶走的熱量占總熱量的30-70%，對這部分熱量的回收利用是鍛造車間節能的重要途徑。目前主要的利用方式是采用預熱器，即利用煙氣余熱對助燃空氣和氣體燃料進行加熱。隨著國家對節能減排的大力推進，余熱二次回收利用技術在鍛造行業中的應用將越來越廣泛。

　　4, the waste heat recovery technology, the flue gas in the fuel furnace temperature is as high as 600-1200 degrees centigrade, take away the heat accounted for 30-70% of the total heat, the recovery of this part of heat is an important way to save energy in the forging workshop. At present, the main mode of utilization is the use of preheater, that is, the use of flue gas waste heat to support combustion air and gas fuel heating. With the country's efforts to promote energy conservation and emission reduction, the application of waste heat two times recycling technology will be more and more widely used in the forging industry.